12VDC@100mA Wall Adapter for 110VAC

12vac/1A wall transformer for 120vac outlet

12VDC@500mA Wall Adapter for 110VAC

6VDC@100mA Wall Adapter for 110VAC

9VDC 100mA Wall Transformer for 110VAC

12VDC@1.0A Wall Adapter for 110VAC

Heavy duty aluminum case, scuff resistant black anodized finish.

6710FP Front Panel 1U standard .125 inch thick 19 X 1.75 inch black anodized, punched and screen printed panel.

Vocoder Kit includes circuit board all electronic parts, switches, jacks controls, knobs and manual.

6720FP Front Panel 1U standard .125 inch thick 19 X 1.75 inch black anodized, punched and screen printed panel.

6720K Quadrafuzz Kit includes circuit board electronic parts, 12VAC wall-mount transformer, switches, jacks, controls, knobs and manual.

6730K Vocal Zapper Kit includes circuit board all electronic parts, switches, jacks and punched, anodized and screen printed front panel.

Kit includes electronic parts, two reverb tanks, circuit board, 1/4" Phone Jacks and manual.

Front panel for the Parametric Equalizer.

For either studio or live performance work, a parametric equalizer is the most powerful and versatile tone control available.

Optional front panel for the 6790K dual limiter kit.

A low noise, low distortion, low cost limiter for even the most budget conscious studios and performers.

Optional front panel for the 9110K direct interface kit.

The Drum Brain firmware converts trigger pulses from eight analog percussion sensors into MIDI Note On/Off and Velocity data.

The MIDI Fader firmware converts eight 0-5V inputs into MIDI Control Change, Pitch Wheel and Channel Pressure messages.

9206K HDA Kit includes electronic parts, circuit board, 1/4" phone jacks, controls and knobs, power supply, case and manual.

1U Rack Panel standard .125 inch thick 19 X 1.75 inch anodized, punched and screen printed panel

9209K Ducker+ Kit includes all electronic components, circuit board, jacks, switches, controls and knobs, wire, Power Supply, etc.

Optional front panel for the 9210K stack-in-a-box kit.

This mono tube pre-amp is optimized for use with guitar.

Eight-channel version of the classic PAiA drum sensor circuit

Optional case for the phantom power pre-amp.

This pre-amp provides phantom power, adjustable gain up to 60 dB and converts balanced inputs into single ended outputs. Kit does not include optional case shown in image.

Drum sounds produced by the 6 Tone Oscillators are individually adjustable from their Nominal sounds.

Option front panel for the 9303K Four Band EQ.

The Four-Band EQ provides up to 16 dB of continuously adjustable Boost or Cut in four overlapping frequency bands from 35Hz to 15kHz.

The TubeHead is a low-cost, two-channel vacuum tube pre-amplifier.

The HiFi version of the TubeHead. Circuitry is identical to the rack mount version.

9308C FatMan desktop case includes anodized and screen printed aluminum and wood case parts and all hardware.

9308FP FatMan 2U Rack Panel standard .125 inch thick 19 X 3.5 inch black anodized, punched and screen printed panel.

Kit includes circuit board, all electronic parts, power supply, wire, hardware, knobs manual.

Optional enclosed case for 2 mic preamps.

The Tube Microphone Pre-amp uses the same warm tube tricks as the TubeHead.

Wooden lectern case for housing the Theremax, includes front panel and antenna mounting hardware.

Theremax front panel and antenna mounting hardware only.

Theremax Theremin based on the same theremin heterodyne principles. Kit includes electronic parts, knobs, wire, circuit board, 12 VDC wall mount power supply. (NO CASE)

The Theremax Theremin electronic kit (9505k) + full wooden lectern case with front panel and antenna mounting hardware (9505C).

Combo set includes the Theremax Theremin electronics kit plus the front panel and antennae mounting hardware.

Theremax is based on the same theremin heterodyne principles, but with embellishments. (NOTE: International version - ships without 110V power supply.)

The Theremax Theremin electronic kit (9505k) + full wooden lectern case (9505C).(NOTE: International version - ships without 110V power supply.)

9506C Project-r* MS Stereo Mic black anodized and legended case including all hardware.

Kit includes electronic parts, electret mic elements, ciruit board, controls, knobs and wall mount power transformer. Does not include case.

Ideal for adding a headphone jack to equipment that lacks one.

9700frm FracRak Accessory Kit adds Transformer, Switch, 8 Stereo Jacks, punched, black anodized,grey legended, 2W FracRak panel and all hardware.

Kit has all electronic parts, circuit board, pc mount DIN jacks and keyboard style DIP switch.

Adds transformer, switch, 16 jacks and fully enclosed 1U rack case with punched, black anodized, grey legended panel and all hardware.

FracRak accessory kits include punched, anodized and screen printed Panel, 1/8" Jacks, hardware and other mechanical parts required to build a FracRak format module.

Combines 3 VCAs, a White Noise Source and full function ADSR/LFO Envelope Generator.

Kits includes punched, anodized and screen printed panel, 1/8" Jacks, hardware and other mechanical parts.

Two independent VCOs with Ramp, Triangle, Sine and Pulse waveforms.

Kits includes punched, anodized and screen printed Panel, 1/8" Jacks, hardware and other mechanical parts.

Two identical, independent filters with Lo Pass, Band Pass and Hi Pass outputs.

Kits include tin-lead plated and solder masked circuit board (4" X 2-3/4"), wall mount transformer and all electronic components.

Kits include tin-lead plated and solder masked circuit board (4" X 2-3/4"), wall mount transformer and all electronic components.

Kits include tin-lead plated and solder masked circuit board (4" X 2-3/4"), wall mount transformer and all electronic components.

RIAA Phono Preamp FracRak panel.

Small (2-1/8" x 2-1/2") RIAA compensated pre-amp to convert vinyl LPs.

Standard size rack panels made of unfinished aluminum...

Double height panel with pre-punched rack mounting ears and blank fronts.

Practice Play Along Kit Available in six weeks.

Envelope Follower Kit

Ultra Fuzz Kit